Manufacturer of Paper Cone & Paper Tube
(An ISO 9001-2008 Certified Company)
» Product Range
» Angle Board Making Machine
Angle Board Making Machine
PAPER EDGE PROTECTOR, as the name defines, is used to
protect the sharp edges of the Glass, Granite, Paper rolls sheet metal rolls
and various special applications
The Paper Edge Protector / Angle Board Making Plant contain the following
- Slitting machine
- Reel Holding stand
- Cascade Gluing system
- Pre forming machine
- On line Gullet Shearing machine
- Fine cutting and wrap Around Punching machine
- Production Capacity 10 meter per minute (depends on the size)
- Product Suitable for 3mm to 6mm thickness and Angle Size 25 x 25 to
100 x 100 mm
- Production Capacity 10 Meter per minute (depends on the size) U
Shape board can also be done by using the Special Attachment.
It is used to slitt the paper to the required width. In this machine, paper
roll having 40 width and 36 dia meter can be loaded and slitted.
There will be 12 Sets of Top and cutters in this machine with adjustable
arrangement. After slitting, Slitted reels will be rewound in two rewinding
shaft. The Tension of the rewinding can be adjusted by means of mechanical
clutches. Master roll can also be adjusted in position and tension.
Minimum 3 tonnes can be slitted in one shift minimum width of the slitting
is 40 mm and maximum will be as per requirement.
Power source : 3 HP AC Motor
Labor required : 1 Person
Qty : 1 No
Reel Holding Stand
Reel Holding stand is used to hold and feed the paper properly into Glue
Cascade system. The number of Stations for paper loading will be 16. From 25
x 25 x 3 mm width to 100 x 100 x 6 mm width paper can be loaded in this
It is made up of MS angles and flats. It is having bottom rollers to adjust
any position during operation.
Cascade Gluing System
It is used to transfer the Glue from Glue tank to paper layers properly. In
this system, there will be Glue tank having stainless steel inner Jacket and
MS outer jacket. Between these two jackets water will be there. The water
will be heated to boil the Glue by means of electric heaters, if necessary.
Glue will be pumped to Paper layers by Gear pump having 110 litres per hour
capacity. In this system there will be paper tension arrangement Glue supply
system and glue scrapper system.
In paper tension arrangement, Paper tension can be adjusted as per
In scrapper system excess glue can be scrapped as per our requirement.
a) Pre forming machine
In this system, the paper layers are feeding into
rotating Rubber roller and formed into the required thickness. Outer layer
having low GSM and low Glue Value is feeding along with these Paper by means
of extra glue arrangement. In this system, the required width and thickness
b) Forming machine
After pre-forming , the papers are fed into
forming machine. In this there are three stations having big angular female
and male rollers with pneumatic operation while the paper is feeding through
system, the angle is formed stage by stage and paper is passed to the
Rollers are driven by 5 H.P DC motor with control. The speed can be
adjusted by means of DC Drive
On Line Guillot
After pre-forming and forming edge protector is passed into on line Guillot
shearing system. It is used to cut the edge protector to the required
length. Guillot shearing is operated by a pneumatic cylinder which is
actuated by electric switch or sensor.
Recutting and Wrap Around Punching Machine
It is used to recut edge protector to the required length of small pieces
and to cut the angle cutting, so that the edge protected can be folded to
the round shape according to the customers requirement In the system a die
is fitted into Power press.
Total Power Requirement
||3 HP AC
|1.5 HP AC +
2 KW Heater
|Pre-forming & morming
||5 HP DC
|Guillot shearing machine
||1.5 HP AC
||1.5 HP AC